Choose the frame rate you will deliver before the wedding, set every camera to it, and pick the shutter speed by the venue's mains frequency rather than by habit. Many lights on mains power pulse at twice its frequency, as flicker research done for the Department of Energy explains: 120 times a second on 60 Hz power, 100 on 50 Hz. A shutter that spans whole pulses hides them. On 60 Hz power that means 1/60 or 1/120; on 50 Hz, 1/50 or 1/100. At 119.88 fps on 50 Hz power, no shutter speed is flicker-free.
Below is the whole chart, worked out for every common wedding frame rate under both kinds of power. It covers which destinations run 50 Hz (Jamaica, Barbados and St. Lucia do, unlike the Bahamas, Mexico and Puerto Rico) and what each slow-motion rate plays back at. It also covers why 23.976 and 24.00 should not share a timeline uncorrected, and how Premiere Pro, DaVinci Resolve and Final Cut Pro handle mixed rates. The rules come from the DOE and its national laboratory, RED's technical guides, the camera makers' manuals and the utilities' own documents. The arithmetic is ours.
Why lights flicker on camera and not to your eye
Mains power alternates, and many lights brighten on each half of the cycle. A review by researchers at Pacific Northwest National Laboratory, published in Lighting Research & Technology in 2023, describes magnetic ballasts producing light "at twice the mains frequency, 100 Hz or 120 Hz for 50 Hz or 60 Hz distribution, respectively". The same lab's 2018 report for the DOE treats a 100 Hz waveform as typical of an LED. Your eye mostly averages that out. A camera taking a short exposure does not: if each frame catches a different slice of the pulse, the picture brightens and dims, or rolls with bands.
Two details matter at weddings. The review notes that early, low-cost "AC-LEDs" can produce "noticeable 120 Hz and 60 Hz modulation in North America", so a cheap string light may pulse at the mains frequency itself, not twice it. And RED's flicker tutorial warns that some neon and LED lights "may flicker independent of the power source". Churches that ban added lights, as 11 of the 28 Catholic parish policies we read do, leave you shooting under the building's own.
The flicker-free shutter chart
RED's rule is to "Choose a shutter speed equal to the lighting pulse rate divided by some integer." On 60 Hz power that gives 1/120, 1/60, 1/40, 1/30 and 1/24; on 50 Hz, 1/100, 1/50, 1/33 and 1/25. A shutter cannot stay open longer than a frame (360 degrees), which is what trims the list at higher frame rates. Here is every safe speed, with its shutter angle:
On 60 Hz power (lights pulse 120 times a second)
- 23.976 or 24 fps: 1/120 (72°), 1/60 (144°), 1/40 (216°), 1/30 (288°), 1/24 (360°).
- 29.97 fps: 1/120 (90°), 1/60 (180°), 1/40 (270°), 1/30 (360°).
- 59.94 fps: 1/120 (180°), 1/60 (360°).
- 119.88 fps: 1/120 (360°) only.
- Above 120 fps: none.
On 50 Hz power (lights pulse 100 times a second)
- 23.976 or 24 fps: 1/100 (86°), 1/50 (173°), 1/33 (259°), 1/25 (345°).
- 25 fps: 1/100 (90°), 1/50 (180°), 1/33 (270°), 1/25 (360°).
- 29.97 fps: 1/100 (108°), 1/50 (216°), 1/33 (324°).
- 50 fps: 1/100 (180°), 1/50 (360°).
- 59.94 fps: 1/100 (216°) only.
- 100 fps: 1/100 (360°) only.
- 119.88 fps: none.
Three things follow. First, the familiar 180 degree shutter is only flicker-free at 29.97 and 59.94 on 60 Hz power, and at 25 and 50 on 50 Hz. At 23.976 in the US, the speed nearest 180 degrees (1/50) is not on the list; use 1/60 or 1/40 under pulsing light. Second, a US crew does not have to switch to 25p abroad: 23.976 at 1/50 is 173 degrees, the figure Blackmagic's 2018 camera manual gives as 172.8 degrees for 24p "in countries with 50 hertz power supplies". Third, 1/60 and 1/30 cover a whole 60 Hz cycle as well as whole 120 Hz pulses, and 1/50 and 1/25 do the same on 50 Hz, so they also hold still under the cheap LEDs that pulse at the mains frequency. 1/120, 1/40, 1/24, 1/100 and 1/33 do not.
Why a wrong shutter at 23.976 looks like a slow swell rather than a flicker: on 60 Hz power, each frame at 23.976 fps lasts just over 5 light pulses, so each frame starts slightly later in the pulse than the one before. In our arithmetic the pattern repeats about every 8 seconds if the grid holds exactly 60 Hz, which reads on screen as the room breathing. At exactly 24.00 fps the frames line up with the pulses, which is why RED's tutorial says that in North America "the standard 24 and 30 fps settings work with most shutter speeds".
Slow motion is where it breaks
The first dance and the sparkler exit happen under the most pulsing light of the day, and they are when you reach for a high frame rate. RED's advice is to "avoid high frame rates (greater than the lighting pulse rate) when possible, or use artificial lighting that provides continuous illumination." On 60 Hz power, 119.88 fps leaves exactly one safe setting, 1/120 at 360 degrees. On 50 Hz power it leaves none, because each light pulse lasts 10 milliseconds and each frame about 8.3.
The fix in a 50 Hz country is 100 fps at 1/100, or 50 fps at 1/100 for 180 degrees. Not every camera offers 100 fps on the US setting. Canon's EOS R6 Mark II manual lists 100.00 and 150.00 fps for "areas where the TV system is PAL", lists 119.88 and 179.82 for NTSC, and makes 23.98 fps "available when" the video system is set for NTSC. On that camera, 100 fps and 23.98 fps sit on opposite sides of one setting. Check yours before the trip.
What each rate plays back at on your timeline, by the arithmetic and by Sony's S&Q table for the FX3:
- 59.94 on a 23.976 timeline: 40% speed ("2.5 times slower", in Sony's table).
- 59.94 on a 29.97 timeline: 50%.
- 119.88 on a 23.976 timeline: 20% ("5 times slower").
- 119.88 on a 29.97 timeline: 25%.
- 100 on a 25 timeline: 25%. On a 23.976 timeline: about 24%.
- 50 on a 25 timeline: 50%. On a 23.976 timeline: about 48%.
Two catches. In-camera slow motion records no sound: Sony's S&Q page says "Sound will not be recorded," and Canon says the same of its High Frame Rate movies. With no sound, sound sync has nothing to line up, so those clips are placed by eye. And higher frame rates fill cards faster: on the FX3, XAVC S-I 4K runs 240 Mbps at 23.98p and 600 Mbps at 59.94p, as our storage arithmetic sets out.
Where the wedding is decides the hertz
The IEC's country list would not load for us, so we went to each place's utility, regulator, law or tourism authority. We used the US Defense Department's Foreign Voltages and Frequencies Guide (2005) only as a cross-check. It agrees for most places but not all: it lists Costa Rica at 50 Hz, where the regulator's standard says 60. Where the two differ, we follow the national source.
50 Hz: use 1/50 or 1/100
- Jamaica. JPS's rate schedule: "Service is alternating current, 50 Hertz".
- Barbados. Barbados Light & Power's tariff page: "alternating current electricity at 50 Hz".
- St. Lucia. The Electricity Supply Act, section 26: "50 cycles per second".
- The UK (Electricity Safety, Quality and Continuity Regulations), Ireland (EirGrid), France (the energy regulator CRE), Italy (Terna's grid code), Spain (Royal Decree 842/2002), Portugal (E-REDES), Greece (IPTO) and Iceland (a 2006 regulation, and the Defense Department guide).
- Bali, under Indonesia's grid code for Java, Madura and Bali.
- Eastern Japan, including Tokyo. Japan's national tourism organization gives "50 Hertz in eastern Japan and 60 Hertz in western Japan (including Nagoya, Kyoto and Osaka)".
60 Hz: use 1/60 or 1/120
- The US (EIA) and Canada (Hydro-Québec's conditions of service, and the Defense Department guide).
- Mexico, in the energy regulator's grid code (Diario Oficial, December 31, 2021).
- Puerto Rico (PREPA's tariff book), the Dominican Republic (Decree 749-02), Costa Rica (the regulator ARESEP) and Belize (Belize Electricity's equipment specification).
- The Bahamas. Bahamas Power and Light delivers "120V / 60Hz" and serves "all the major islands of the Bahamas exclusive of Grand Bahama", so that statement does not cover Grand Bahama.
- Turks and Caicos (Pelican Energy TCI: "110 volt/60 cycle"), the Cayman Islands (its Department of Tourism) and Bermuda (its Tourism Authority).
- Colombia, including Cartagena (the regulator CREG).
- Western Japan, including Kyoto and Osaka.
Two gaps. Antigua and Barbuda's tourism authority says "240 Volts, 50 cycles AC (a few hotels are 110 Volts, 60 cycles)", while the Defense Department guide lists 60, and we found nothing from the utility. We found no current official statement for the US Virgin Islands or Aruba; the Defense Department guide lists "Virgin Islands" and Aruba's capital at 60. In any of these, run the test in the callout below.
23.976 is not 24
ITU-R BT.709, the HD television standard, specifies 24, 30 and 60 frames a second and "those values divided by 1.001", which is where 23.976, 29.97 and 59.94 come from. The gap is about 0.1%: 3.6 seconds an hour, or one frame every 41.7 seconds at 24. Count frames per beat at 24 on a 23.976 timeline and the same gap walks the cuts off a song, a frame every 41.7 seconds, as how to edit a wedding highlight film works out.
Of the cameras we checked, only some offer true 24.00. Canon's R6 Mark II lists 23.98 fps "Mainly for cinematic purposes" and no 24.00. Sony's FX3 records 24.00p only in its DCI 4K intraframe format, on firmware 3.00 or later, and the A7S III gets it through a separate "DCI 4K / 24.00p Upgrade License". Panasonic's S5II has a "24.00Hz (CINEMA)" system frequency, and Blackmagic's Pocket cameras offer both. So a crew with mixed bodies can end up with both rates without meaning to.
How you join them matters. Premiere's Interpret Footage reassigns a clip's frame rate, and Adobe says that "audio is changed in addition to the video" and that the duration changes in proportion. Interpret a 24.00 ceremony clip as 23.976 and its 45 minutes run about 2.7 seconds longer, picture and sound, against every other camera. In DaVinci Resolve, changing a clip's Video Frame Rate attribute changes its speed, but "A clip's audio, however, will be unaffected." Neither is a conform. Leave the clip at its real rate and let the editor retime it to the timeline, or better, set every camera to the same rate. Clock drift between recorders is a separate, smaller problem, covered in our post on audio sync drift.
Mixed frame rates in Premiere, Resolve and Final Cut
- Premiere Pro. "Sequence settings like time base are locked once the sequence is created," says Adobe's sequence help. A multicam source sequence's preset defaults to Automatic, "based on the video format of the Camera 1 clip", so make Camera 1 an angle shot at your delivery rate.
- DaVinci Resolve. Set the timeline frame rate before importing anything: once media is in the Media Pool it "cannot be changed", and the same goes for "Mixed frame rate format". With that set to "Resolve" (the manual's advice when editing from scratch), "Clips with different source frame rates will be retimed to match the Timeline conform frame rate." Set to "None", they play frame for frame at the timeline rate, "resulting in either faster or slower motion".
- Final Cut Pro. Multicam clips "can be made up of diverse media sources (different formats, frame rates, and so on)", and by default take "the most common clip properties among those clips". A clip at another rate is conformed with Frame Sampling, whose default is "Fast (Floor)". For slow motion, Automatic Speed plays every frame at the project rate, so "no frames are skipped or duplicated".
What each editor costs, and how each handles a Sony FX3's files, is in Resolve Studio against Premiere.
24 or 30: what actually decides it
No standard picks the look for you. Adobe's sequence settings reference says to "choose 24 for editing motion-picture film, 25 for editing PAL (European standard) and SECAM video, and 29.97 for editing NTSC (North American standard) video", and Blackmagic's manual says "let your delivery format guide your choice." For online delivery, the platforms want what you shot. YouTube: "Content should be encoded and uploaded in the same frame rate it was recorded." Vimeo: keep the native rate, constant, and above 60 fps "we will automatically reduce the frame rate." Meta's developer documentation gives 23 to 60 fps for Instagram Reels and 24 to 60 for Facebook Reels.
The one practical difference is movement. RED's panning guide gives a rule of thumb for 24 fps at 180 degrees: "pan no faster than a full image width every seven seconds". It notes that a higher frame rate changes the result. A fast gimbal orbit of the couple judders more at 24 than it does played back at 30 or 60. If you shoot 24 for its look, slow the camera down or let the move blur.
Camera settings that help
- Blackmagic. The Pocket Cinema Camera suggests up to three flicker-free shutter values for your frame rate, worked out from a 50Hz or 60Hz setting in its setup menu. Set it for the destination.
- Sony FX5. Its Shooting menu has Flicker Reduce, off by default, with a 50Hz or 60Hz frequency whose default "varies depending on the country or region of purchase". A body bought in the US may need it changed for Jamaica.
- Sony FX30 and Panasonic. Sony's Variable Shutter adjusts the shutter in fine steps "according to the flickering frequency", and Panasonic's Synchro Scan does the same on the S5II and GH6. Use them for LEDs whose flicker is not tied to the mains.
- Canon. The R6 Mark II manual's troubleshooting suggests a slower shutter speed when movies flicker, and gives no list of safe speeds.
Blackmagic and RED end on the same caveat. RED says to "always capture test footage", and Blackmagic that "the characteristics of individual light sources may still cause flicker even when using flicker free values. We recommend always performing a test shoot".
A frame rate checklist for the wedding
- Decide the delivery rate when you book, and write it on the shot list.
- Set every camera, including the second shooter's and the drone, to that rate, 23.976 and not 24.00 unless all of them can do 24.00.
- Look up the destination's mains frequency, or run the hertz test on arrival, and set the camera's 50/60 Hz option to match.
- Under the venue's lights, use 1/60 (or 1/50 abroad) unless you have tested another speed.
- For slow motion, shoot a multiple of the delivery rate, check the chart above, and plan to place those clips by eye.
- Set the timeline rate before importing, and make Camera 1 an angle at the delivery rate.
Common questions
- What is the best frame rate for wedding videos?
- No standard picks it for you. Adobe's Premiere guidance gives 24 for film, 25 for PAL regions such as Europe and 29.97 for NTSC regions such as North America. What matters more is that every camera records the rate you will deliver, set before the day, with slow motion at a multiple of it. YouTube asks for video uploaded at the frame rate it was recorded, and Vimeo for the native rate, held constant.
- What shutter speed stops LED flicker in wedding video?
- One that lasts a whole number of light pulses. Lights pulse at twice the mains frequency, so under 60 Hz power (the US, Canada, Mexico) use 1/60 or 1/120, and under 50 Hz power (Europe, Jamaica, Barbados) use 1/50 or 1/100. At normal frame rates the safest single choice is 1/60 under 60 Hz and 1/50 under 50 Hz, because those also cover cheap LEDs that pulse at the mains frequency itself.
- Why does my slow motion flicker at the reception?
- Because each frame at 119.88 fps lasts about 8.3 milliseconds. Under 60 Hz light the only flicker-free shutter is 1/120, a 360 degree shutter. Under 50 Hz light no shutter speed works at all, because each light pulse lasts 10 ms, longer than the frame. In a 50 Hz country, shoot 100 fps at 1/100 if your camera offers it, or 59.94 fps at 1/100.
- Is 23.976 fps the same as 24 fps?
- No. ITU-R BT.709 specifies 24 frames a second and 24 divided by 1.001, which is 23.976. The gap is about 0.1%: 3.6 seconds an hour, or one frame every 41.7 seconds. Some cameras offer only 23.976 on their US setting, and some offer true 24.00 only in a cinema mode. Mixing the two in one multicam edit needs a conform, not a reinterpretation.
- Which Caribbean wedding destinations use 50 Hz power?
- Jamaica, Barbados and St. Lucia, according to JPS's rate schedule, Barbados Light & Power and St. Lucia's Electricity Supply Act. Antigua is unclear: its tourism authority says 50 cycles with a few hotels at 60, and the US Defense Department's guide says 60. The Bahamas (outside Grand Bahama), Mexico, Puerto Rico, the Dominican Republic, Turks and Caicos, Cayman and Bermuda run 60 Hz.
- Can I mix frame rates in a multicam wedding edit?
- Yes, as long as the editor conforms them to one timeline rate. Set that rate first: Premiere locks a sequence's time base once it is created, and DaVinci Resolve will not change the timeline frame rate once media is in the Media Pool. Premiere's multicam source sequence takes its format from the Camera 1 clip by default, and Final Cut Pro picks the most common properties among the clips.

